My chevy truck 80

[bobchevytruck80]

Presentation of my chevy truck after 25 years of work


After the first part of recovery


My new engine


My monster garage


Bob

[texasredneck]

nice 1980, merveilleux 1980, mooie 1980 :-)

[Pontiac1976]

Nice job looks pretty good even after 25 yr work

[bobchevytruck80]

Bonjour à tous
Hello Mani

help

Je suis au remontage du moteur de mon chevy truck de 1980 et j’ai quelques problèmes
I am with the reassembly of the engine of my chevy truck of 1980 and I have some problems
Description :
Le moteur est un chevy de GM performance
The engine is a chevy GM performance
Je place sur le moteur un Kit poulie March performance
I place on the engine a Kit pulley March performance
Problème :
La poulie de la pompe à huile à un trou trop grand pour l’axe de la pompe
The pulley of the oil pump with a too large hole for the axis of the pump
Donc pas possible de la fixer sur la pompe .
Thus not possible to fix it on the pump
La pompe est une tuff stuff chromée la poulie march N° 6..
The pump is a tuff stuff chrome the pulley march N° 6….
Je place des photos et les références demain
I place photographs and the references tomorrow
Avez-vous déjà eu ce problème ou existe-t-il une pièce qui ce place dans le trou de la poulie ou dois-je faire la pièce
You already had this problem or exists it a part which this place in the hole of the pulley or must I make the part

tank you
Bob

[bobchevytruck80]

Which is the part which goes in the center of the pulley

help my
tank you
Bob

[Pontiac1976]

texasredneck maybe you can help me under stand the question better.
Yes March pulleys are nice I take a stab at this any how you pump is leaking at he shaft seal of the tank ?
If it's leaking any where around there the pulley has to come off replace the pump or fix it.
you would need a power steering pump pulley remover. Now it's hard to see but it looks all most like the pulley might be put on back wards.
that will make taking off the pulley hard.
If not then I would rent or buy a power steering pump pulley Remover Installer to do work on those types your self.
if the pulley was put on back wards then you might have to take it to a some one that has puller that may work on that pulley since if it's on the wrong way the two groves will not be able to hook up the right puller. Then you will have to three or four arm puller try to hook in the belt area this may make the pulley no good.!

Did I hit on any of the points you needed I can get you a # for the puller I use the full kit is better because you can put the pulley back on again.

[texasredneck]

hey pontiac,

he says that the hole in the pulley is too big for the steering pump axl,his pulley is a march nr 6 and the steering pump the tuff stuff brand. have you allready had this problem, is there somethi,ng thta exists to make it fit?
i'm checkn out my steering pump and pulley tomorrow , to see how its fixed,i guess if he mounted the pulley backwards the belt won't be line up straight, no?

[bobchevytruck80]

Thank you for your 1st answer Pontiac 1976

J’ai peu être mal expliqué. Mon anglais est primitif
I have to be badly explained little. My English is primitive
La pompe est nouvelle et la poulie aussi
The pump is new and the pulley too
Tout est un kit march nouveau jamais placé sur le moteur et acheté il y a déjà 4 ou 5 années
All is a new kit march ever placed on the engine and bought there are already 4 or 5 years
Simplement l’axe de la pompe est plus petit que le trou dans la poulie
Simply the axis of the pump is smaller than the hole in the pulley
Il y a peu être une bague ou un autre système pour calé la poulie qui n’est pas fourni dans le kit
There is to little be a ring or another system for fixed the pulley which is not provided in the kit

[bobchevytruck80]

Hey texasrednck
You posted in same time that me and you saw the problem just I tomorrow to the garage will take measurements of the parts and N° exact to communicate to you
Bob

[bobchevytruck80]

Vous comprendrez certainement mieux que moi
You will include/understand certainly better than me???
www.marchperf.com/pg66.html

[texasredneck]

it seems that there are 6 different tuff stuff steering pump models so: or the steering pump is wrong or the pulley ...pulleys are screwed on the steering pump with a kit that is mostly with the pump or pulley it's nothing more than a bolt, nut and washer but you have to place the pulley on the steering pump shaft , put the bolt in the shaft with the nut and washer and tighten the pulley on the pump by wrenching it on...so, if the hole in the pulley is too big then it's either a wrong pump or pulley...nothing extra is needed to fix the pulley on the pump....

[bobchevytruck80]

Hey kurt
Je suis allé au garage aujourd’hui prendre les mesures.
I went to the garage to take measurements today.
La pompe ancienne à un axe de 19 mm = 3/8
The old pump with an axis of 19 mm = 3/8
La poulie est mise à la presse.
The pulley is put at the press
La nouvelle pompe à un axe de 16 mm avec une clavette.
The new pump with an axis of 16 mm with a key
J’ai recherchez dans le catalogue, ma poulie n° 617 = le trou 19 mm
I have seek in the catalogue, my pulley n° 617 = the hole 19 mm
La bonne poulie pour ma pompe doit être la n° 616 = le trou de 16 mm avec rainure pour clavette.
The good pulley for my pump must be the n° 616 = the hole of 16 mm with groove for key.
No problemo !
Reste à commander 1 poulie N° 616 et 1 fan extantion N° 353 et çà devrait tourner
Remain to order 1 pulley N° 616 and 1 fan extantion N° 353 and that should turn
www.marchperf.com/pg5.html
Merci de votre aide
Thank you for your assistance

Bob

[Pontiac1976]

Yes there is different size shaft pulleys but it should be snugg. And the pulley should have notch grove around that the pulley fit in the pull it off. Do you have A/c or a AIR PUMP on the truck.there two main sizes on them from 73 - 80 with the single groove pulley off hand I do not know the sizes